A brand-new heat-pump compressor for Model 3 & Y.
Not remanufactured. Not a rebuilt core. A forward-engineered 41 cc electric compressor that replaces both the Denso and the Sanden original — and clears the W139 and W219 codes that keep coming back.
The heat pump is the second most-replaced part on a Tesla.
An electric scroll compressor runs all year, spins to 8,000 rpm and shares one compression chamber. When it wears out, the quote from a dealer or independent shop usually runs into four figures — which is why so many cars end up with a used part and a 90-day promise.
Seven changes that matter after the warranty ends.
The ESH41 was designed for the replacement market from a clean sheet: every high-wear assembly was re-specified instead of copied.
Floating seal strip
The back-pressure seal is replaced by a floating strip that tolerates debris and repeated heat cycles better than the original lip seal.
Forged 4032 scroll set
New profile equation, 8% thicker scroll wall, 4032 forged aluminium with T6 heat treatment, then nickel plating at HV500–700.
Automotive-grade controller
Texas Instruments automotive MCU with over-temperature and over-current protection, running our own control algorithm.
Denso and Sanden compatible
One control program talks to both factory protocols, so a single SKU covers both builds and clears W139 / W219.
Reinforced motor
OEM-grade motor with double varnish impregnation and a redesigned refrigerant path that reduces aluminium-particle erosion.
Terminal moved out of the oil
The 380 V terminal block is rotated 90° so it sits above the oil sump instead of soaking in it — fewer insulation faults.
New housing tooling
A dedicated mould, not a reworked core. As of 2026 only two companies in the replacement market run brand-new tooling.
Premium consumables
Shin-Etsu grease, Chevron Rykon POE oil, nitrided C&U bearings and Sandvik 20C valve steel.
ESH41 technical data
Data from the supplier test sheet. Bench values measured with R134a; R1234yf behaves the same within normal operating range.
| Part number | ESH41 (41 cc electric scroll) |
|---|---|
| Application | 2021–present Model 3, 2020–present Model Y, heat-pump vehicles |
| Replaces (Denso) | 1501256-00J / 00K / 00L / 00M |
| Replaces (Sanden) | 1582668-00F / 00H / 00I / 09J |
| Supply voltage | DC 350–400 V |
| Cooling capacity | 4.5 kW at 4,000 rpm |
| COP | 2.1 |
| Weight | 7.45 kg including oil |
Which cars this fits
The ESH41 covers the 41 cc heat-pump system used on Model 3 and Model Y. Open the frunk, remove the plastic cover on the left: if you see the octovalve module next to a 41 cc compressor, this is the right part.
- Model Y — 2020 – present, All trims with heat pump
- Model 3 — 2021 – present, Heat-pump vehicles only
- Always confirm by VIN before ordering. Send us the VIN and a photo of the compressor label and we will check it against the OEM number for you.
One order, everything the job needs.
Compressor + 8-piece repair kit
Everything except labour. Ships as one carton with the compressor.
- ESH41 compressor × 1
- A/C heat exchanger (LCC) × 1
- Battery coolant heat exchanger × 1
- Branded refrigerant × 6
Full repair package
The same kit plus the work, at a partner workshop. Available in selected markets — ask for coverage.
- Full system flush service
- Compressor and heat-pump replacement
- 12-month workmanship warranty
Before you order
Is this a new part or a rebuilt one?
New. The scroll set, controller, motor and housing are produced with new tooling. We do not sell rebuilt or re-sealed cores.
Will it fit my car?
It fits 2021 and newer Model 3 and 2020 and newer Model Y with the heat-pump system (41 cc compressor next to the octovalve). Earlier cars with a PTC heater use a different compressor. Send us the VIN and we will confirm before you pay.
Does it work with both Denso and Sanden cars?
Yes. One controller covers both factory protocols, which is why a single SKU replaces Denso 1501256-00J/K/L/M and Sanden 1582668-00F/H/I/09J.
Do I need a dealer software update?
No re-flash is required. The controller identifies the vehicle protocol on start-up, and the W139 / W219 codes that appear with rebuilt units do not return.
Do I have to flush the system?
Yes, always. Debris from a failed compressor circulates through the loop and will damage the new unit within days. A system that was not flushed is excluded from warranty.
What refrigerant and oil does it use?
R1234yf or R134a, with 250 ml of POE 68 oil pre-filled at the factory. Do not add oil.
What does the warranty cover?
12 months or 12,000 miles, whichever comes first, for parts and labour. Register the unit with the QR card in the box. Failures caused by debris, wrong refrigerant or installation errors are excluded.
Need a fitment check or a price?
Tell us the model year and the VIN. We will confirm the part, the freight and the lead time — usually the same working day.
Request a quote
No account needed. We reply within one business day.